PSP をしている上でさまざまな 「エラーコード」 がでることがあります。
それをまとめてみましたので何が原因かを確かめたいときに使ってみてください。
＜使い方＞
PSP 上で何かエラーコードが表示されたとき、そのコードを記録しておき、
このページからCtrl＋Fで検索ができます。
| エラーコード |
症状 |
| UKN9000001 |
アップデートが開始できませんでした。
データが破損しています。 |
| 80110305 |
読み込みができませんでした。
メモリースティックにアクセスできません。 |
| 80010013 |
デバイスまたはメディアが見つかりませんでした。 |
| 8001B002 |
原因不明です。 |
| 80020001 |
カーネルエラーです。
使用するカーネルを変更して下さい。 |
| 800244C |
カーネルエラーです。
使用するカーネルを変更して下さい。 |
| 80020001 |
一般的なカーネルエラーです。 |
| 800200D9 |
メモリブロックを割り当てられませんでした。 |
| 80020130 |
ファイルが誤っています。
リカバリーモードより「Advanced configration」→「Execute boot.bin in UMD/ISO」をDisabledにして下さい。 |
| 80020148 |
サポートされていないPRXを使用しています。
リカバリーモードより「Advanced configration」→「Execute boot.bin in UMD/ISO」をDisabledにして下さい。 |
| 80110482 |
WLAN接続に失敗しました。 |
| FFFFFED3 |
複合化に失敗しています。 |
| 80410001 |
ネットワークエラーです。 |
| 80410D16 |
ネットワークエラーです。 |
| 80410D07 |
恐らくWLAN関係のエラーです。 |
| ffffffff |
アップデートに失敗しました。 |
| 80410A0B |
内部エラーです。 |
| 80410410 |
アクセスポイントに接続できませんでした。 |
| 80010087 |
ゲームを開始することができませんでした。 |
| 80020002 |
実行できませんでした。 |
| 80020032 |
illegalexcepti コードエラー |
| 800200cb |
UIDが不明です。 |
| 800200cc |
UIDが当っていません。 |
| 8002012e |
モジュールが見つかりませんでした。
|
| 8002012f |
モジュールファイルが見つかりませんでした。 |
| 80020130 |
モジュールファイルの読み込みに失敗しました。 |
| 80020132 |
モジュールの配置がおかしいです。 |
| 80020133 |
モジュールの開始準備ができませんでした。 |
| 80020032 |
不法な例外です。 |
| 80020321 |
使用するデバイスが間違っています。
リカバリーモードかVSHMenu で 「UMD ISO MODE」を M33 driver や Sony NP9660 などに変更して下さい。 |
| 800201a8 |
タイムアウトです。 |
8002012d |
対象は PRX/PFX でない、不正な形式です。
リカバリーモードより「Advanced configration」→「Plain module in UMD/ISO」をEnabledにして下さい。 |
・CA000005 = keys.bin not found when trying to run a PS1 game.
・DADADADA = Running a FW Update in DAX custom FW
・FFFFFFFF = PSP update failed
・UKN9000001 = update cant start, data corrupt
・00000001 = WiFi error. Occurs when no access points are detected in official 3.7X and custom 3.7X firmware.
・80010087 = Error reading UMD or UMD not present
・80110305 = Load failed.The Memory Stick could not be acessed
・80020148 = Unsupported PRX type | This error also seems to appear when you are running an iso with a fake mem. stick
・8001006F = Remote Play connection error. Most likely when no PS3 is sending a signal over your network.
・800200D1 = Ran homebrew without Homebrew enabled firmware.
・8002014C = Ran kxploited homebrew without Homebrew enabled firmware.
・80020321 = Ran a game that doesn't support NO-UMD* (DAX FW ONLY!)
・80110404 = Network error, try restore default settings to fix
・80000004 = its just a general error code that the PSP spits out when it doesnt understand something could mean anything
・80110307 = Load Failed There is no Data available
・80010002 = Putting the POPS EBOOT in the wrong folder
・80000001 = Got it when trying to run PSP filer version 3.6 on 3.40* firmware
・80410A0B = Loose WiFi card
・80020321 = No umd in drive when no umd is disabled
・80110305 = Load failed.The Memory Stick could not be acessed
・8001006F = Remote Play connection error. Most likely when no PS3 is sending a signal over your network
・80020148 = Unsupported PRX type
・800200D1 = Ran homebrew without Homebrew enabled firmware
・8002014C = Ran kxploited homebrew without Homebrew enabled firmware
・80020321 = No umd in drive when no umd is disabled / Ran a game that doesn't support NO-UMD / "No-UMD Mode"
・98765432 = Selected a language who's font has been removed. DAX FW ONLY ERROR!
・80020148 = (unsupported PRX type)?
・800201A8 = (WAIT timeout)?
・80020130 = File Read Error (ex. length is 0)
・80020001 = Generic Kernel Error = default (ex. executable is invalid)
・800200D9 = Failure to allocate memory block (ex. missing PSP)
・80410D07 = Connection error has occurred. (Ie cant find access pt)
・80020001 = error
・80020002 = not implemented
・80020032 = illegal exception code
・80020033 = exception handler not use
・80020034 = exception handler already used
・80020035 = system call table not use
・80020036 = system call table already used
・80020037 = illegal system call table
・80020038 = illegal Primary Syscall number
・80020039 = Primary Syscall number already use
・80020064 = call from interrupt handler/thread
・80020065 = illegal INTRCODE
・80020066 = CPU already interrupt disable
・80020067 = Handler already exist
・80020068 = Handler not found
・80020069 = illegal interrupt level
・8002006a = illegal address
・8002006b = illegal Intr Handler Option Param size
・8002006c = illegal stack address
・8002006d = already stack address set
・80020096 = not found free Hard Timer
・80020097 = illegal timer ID
・80020098 = illegal source
・80020099 = illegal prescale
・8002009a = Hard Timer in use
・8002009b = Hard Timer not setup
・8002009c = Hard Timer not in use
・800200a0 = unit number already used
・800200a1 = unit number not used
・800200a2 = rom directory not found
・800200c8 = id type already exist
・800200c9 = id type not exist
・800200ca = {not available}
・800200cb = unknown UID
・800200cc = unmatch UID type
・800200cd = id not exist
・800200ce = not found UID function
・800200cf = UID already holder
・x800200d0 = UID not holder
・800200d1 = illegal permission
・800200d2 = illegal argument
・800200d3 = illegal address
・800200d4 = the memory area is out of range
・800200d5 = the memory area is overlap
・800200d6 = illegal partition id
・800200d7 = partition in use
・800200d8 = illegal memory block allocation type
・800200d9 = failed to allocate memory block
・800200da = inhibited to resize this memory block
・800200db = failed to resize this memory block
・800200dc = failed to allocate heap block
・800200dd = failed to allocate heap
・800200de = illegal chunk id
・800200df = cannot find chunk name
・800200e0 = there is no free chunk
・8002012c = module link error
・8002012d = illegal object format (not PRX/PFX)
・8002012e = not found Module
・8002012f = not found Module file
・80020130 = Module file read error
・80020131 = memory in use
・80020132 = partition mismatch
・80020133 = module already started
・80020134 = module not started yet
・80020135 = module already stopped
・80020136 = module cannot stop
・80020137 = module not stopped yet
・80020138 = module cannot remove
・80020139 = exclusive load
・8002013a = Library is not linked yet
・8002013b = Library already exists
・8002013c = Library not found
・8002013d = illegal Library header
・8002013e = Library isused now
・8002013f = module already stopping
・80020140 = illegal off set value
・80020141 = illegal position code
・80020142 = illegal access code
・80020143 = module manager busy
・80020144 = illegal flag
・80020145 = cannot get module list
・80020146 = prohibit Load Module device
・80020147 = prohibit Load Exec device
・80020148 = unsupported PRX type
・80020149 = illegal permission call
・8002014a = cannot get module information
・8002014b = illegal Load Exec buffer
・8002014c = illegal Load Exec file name
・8002014d = There is no exit callback
・80020190 = no memory
・80020191 = illegal attr parameter
・80020192 = illegal thread entry address
・80020193 = illegal priority value
・80020194 = illegal stack size
・80020195 = illegal mode
・80020196 = illegal mask
・80020197 = illegal thread ID
・80020198 = not found thread
・80020199 = not found semaphore
・8002019a = not found event flag
・8002019b = not found message box
・8002019c = not found Vpool
・8002019d = not found Fpool
・8002019e = not found message pipe
・8002019f = not found alarm
・800201a0 = not found thread event handler
・800201a1 = not found callback
・800201a2 = thread already DORMANT
・800201a3 = thread already SUSPEND
・800201a4 = thread is not DORMANT
・800201a5 = thread is not SUSPEND
・800201a6 = thread is not WAIT
・800201a7 = now dispatch disabled
・800201a8 = WAIT timeout
・800201a9 = WAIT canceled
・800201aa = WAIT status released
・N800201ab = WAIT status released with callback
・800201ac = thread is terminated
・800201ad = semaphore counter zero
・800201ae = semaphore counter overflow
・800201af = event flag condition not occur
・800201b0 = this event flag cannot accept waits with multiple threads
・800201b1 = illegal event flag wait pattern
・800201b2 = message box have no message
・800201b3 = message pipe is full
・800201b4 = message pipe is empty
・800201b5 = wait object deleted
・800201b6 = illegal memory block
・800201b7 = illegal memory size
・800201b8 = illegal scratchpad address
・800201b9 = scratch pad in use
・800201ba = scratchpad not in use
・800201bb = illegal type
・800201bc = illegal size
・800201bd = illegal count
・800201be = not found vtimer
・800201bf = illegal vtimer ID
・800201c0 = illegal KTLS ID
・800201c1 = KTLS is full
・800201c2 = KTLS is busy
・80020258 = invalid such priority
・80020259 = device name is invalid
・8002025a = device name is unknown
・8002025b = pm information is registered already
・8002025c = pm information is not registered
・8002025d = major state is invalid value
・8002025e = request is invalid
・8002025f = request is unknown
・80020260 = unit number is invalid
・80020261 = cannot cancel request
・80020262 = pm information is invalid
・80020263 = argument is invalid
・80020264 = already target epower state
・80020265 = failed to change system power state
・80020266 = cannot change device power state
・80020267 = device does not support such power state
・800202bc = request to the DMAC failed
・800202bd = DMA operation is less or equal one
・800202be = the operation is already queued
・800202bf = the operation is already finished or not queueud
・800202c0 = the operation is already in transfer progress
・800202c1 = the operation is not assigned yet
・800202c2 = the sync operation timed out
・800202c3 = dma operation struct is already freed
・800202c4 = dma operation is used
・800202c5 = dma operation is empty
・800202c6 = DMA operation is aborted
・800202c7 = DMA operation is error
・800202c8 = physical DMA channel is already reserved
・800202c9 = physical DMA channel is not managed by dmac manager
・800202ca = there is a privilege address in link list
・800202cb = link list buffer is not enough
・800202cc = the operation is not assigned to physical DMA channel
・800202cd = the operation is child operation
・800202ce = it is too much than transferable datasize
・800202cf = argument is invalid
・80020320 = Too many open files
・80020321 = No such device
・80020322 = Cross-device link
・80020323 = Bad file descriptor
・80020324 = Invalid argument
・80020325 = Unsupported operation
・80020326 = Alias is already used
・80020327 = Cannot mount
・80020328 = Driver deleted
・80020329 = Async operation is busy
・8002032a = No async operation
・8002032b = Device is already registered
・8002032c = No current working directory
・8002032d = Filename too long
・800203e8 = DECI3 No such device or address
・800203e9 = DECI3 I/O error
・800203ea = DECI3 Not enough core
・800203eb = STDIO not opened
・8002044c = Parameter is not cache aligned
・8002044d = End of kernel error code Never use this name
＜使い方＞
PSP 上で何かエラーコードが表示されたとき、そのコードを記録しておき、
このページからCtrl＋Fで検索ができます。
| エラーコード |
症状 |
| UKN9000001 |
アップデートが開始できませんでした。
データが破損しています。 |
| 80110305 |
読み込みができませんでした。
メモリースティックにアクセスできません。 |
| 80010013 |
デバイスまたはメディアが見つかりませんでした。 |
| 8001B002 |
原因不明です。 |
| 80020001 |
カーネルエラーです。
使用するカーネルを変更して下さい。 |
| 800244C |
カーネルエラーです。
使用するカーネルを変更して下さい。 |
| 80020001 |
一般的なカーネルエラーです。 |
| 800200D9 |
メモリブロックを割り当てられませんでした。 |
| 80020130 |
ファイルが誤っています。
リカバリーモードより「Advanced configration」→「Execute boot.bin in UMD/ISO」をDisabledにして下さい。 |
| 80020148 |
サポートされていないPRXを使用しています。
リカバリーモードより「Advanced configration」→「Execute boot.bin in UMD/ISO」をDisabledにして下さい。 |
| 80110482 |
WLAN接続に失敗しました。 |
| FFFFFED3 |
複合化に失敗しています。 |
| 80410001 |
ネットワークエラーです。 |
| 80410D16 |
ネットワークエラーです。 |
| 80410D07 |
恐らくWLAN関係のエラーです。 |
| ffffffff |
アップデートに失敗しました。 |
| 80410A0B |
内部エラーです。 |
| 80410410 |
アクセスポイントに接続できませんでした。 |
| 80010087 |
ゲームを開始することができませんでした。 |
| 80020002 |
実行できませんでした。 |
| 80020032 |
illegalexcepti コードエラー |
| 800200cb |
UIDが不明です。 |
| 800200cc |
UIDが当っていません。 |
| 8002012e |
モジュールが見つかりませんでした。
|
| 8002012f |
モジュールファイルが見つかりませんでした。 |
| 80020130 |
モジュールファイルの読み込みに失敗しました。 |
| 80020132 |
モジュールの配置がおかしいです。 |
| 80020133 |
モジュールの開始準備ができませんでした。 |
| 80020032 |
不法な例外です。 |
| 80020321 |
使用するデバイスが間違っています。
リカバリーモードかVSHMenu で 「UMD ISO MODE」を M33 driver や Sony NP9660 などに変更して下さい。 |
| 800201a8 |
タイムアウトです。 |
8002012d |
対象は PRX/PFX でない、不正な形式です。
リカバリーモードより「Advanced configration」→「Plain module in UMD/ISO」をEnabledにして下さい。 |
・CA000005 = keys.bin not found when trying to run a PS1 game.
・DADADADA = Running a FW Update in DAX custom FW
・FFFFFFFF = PSP update failed
・UKN9000001 = update cant start, data corrupt
・00000001 = WiFi error. Occurs when no access points are detected in official 3.7X and custom 3.7X firmware.
・80010087 = Error reading UMD or UMD not present
・80110305 = Load failed.The Memory Stick could not be acessed
・80020148 = Unsupported PRX type | This error also seems to appear when you are running an iso with a fake mem. stick
・8001006F = Remote Play connection error. Most likely when no PS3 is sending a signal over your network.
・800200D1 = Ran homebrew without Homebrew enabled firmware.
・8002014C = Ran kxploited homebrew without Homebrew enabled firmware.
・80020321 = Ran a game that doesn't support NO-UMD* (DAX FW ONLY!)
・80110404 = Network error, try restore default settings to fix
・80000004 = its just a general error code that the PSP spits out when it doesnt understand something could mean anything
・80110307 = Load Failed There is no Data available
・80010002 = Putting the POPS EBOOT in the wrong folder
・80000001 = Got it when trying to run PSP filer version 3.6 on 3.40* firmware
・80410A0B = Loose WiFi card
・80020321 = No umd in drive when no umd is disabled
・80110305 = Load failed.The Memory Stick could not be acessed
・8001006F = Remote Play connection error. Most likely when no PS3 is sending a signal over your network
・80020148 = Unsupported PRX type
・800200D1 = Ran homebrew without Homebrew enabled firmware
・8002014C = Ran kxploited homebrew without Homebrew enabled firmware
・80020321 = No umd in drive when no umd is disabled / Ran a game that doesn't support NO-UMD / "No-UMD Mode"
・98765432 = Selected a language who's font has been removed. DAX FW ONLY ERROR!
・80020148 = (unsupported PRX type)?
・800201A8 = (WAIT timeout)?
・80020130 = File Read Error (ex. length is 0)
・80020001 = Generic Kernel Error = default (ex. executable is invalid)
・800200D9 = Failure to allocate memory block (ex. missing PSP)
・80410D07 = Connection error has occurred. (Ie cant find access pt)
・80020001 = error
・80020002 = not implemented
・80020032 = illegal exception code
・80020033 = exception handler not use
・80020034 = exception handler already used
・80020035 = system call table not use
・80020036 = system call table already used
・80020037 = illegal system call table
・80020038 = illegal Primary Syscall number
・80020039 = Primary Syscall number already use
・80020064 = call from interrupt handler/thread
・80020065 = illegal INTRCODE
・80020066 = CPU already interrupt disable
・80020067 = Handler already exist
・80020068 = Handler not found
・80020069 = illegal interrupt level
・8002006a = illegal address
・8002006b = illegal Intr Handler Option Param size
・8002006c = illegal stack address
・8002006d = already stack address set
・80020096 = not found free Hard Timer
・80020097 = illegal timer ID
・80020098 = illegal source
・80020099 = illegal prescale
・8002009a = Hard Timer in use
・8002009b = Hard Timer not setup
・8002009c = Hard Timer not in use
・800200a0 = unit number already used
・800200a1 = unit number not used
・800200a2 = rom directory not found
・800200c8 = id type already exist
・800200c9 = id type not exist
・800200ca = {not available}
・800200cb = unknown UID
・800200cc = unmatch UID type
・800200cd = id not exist
・800200ce = not found UID function
・800200cf = UID already holder
・x800200d0 = UID not holder
・800200d1 = illegal permission
・800200d2 = illegal argument
・800200d3 = illegal address
・800200d4 = the memory area is out of range
・800200d5 = the memory area is overlap
・800200d6 = illegal partition id
・800200d7 = partition in use
・800200d8 = illegal memory block allocation type
・800200d9 = failed to allocate memory block
・800200da = inhibited to resize this memory block
・800200db = failed to resize this memory block
・800200dc = failed to allocate heap block
・800200dd = failed to allocate heap
・800200de = illegal chunk id
・800200df = cannot find chunk name
・800200e0 = there is no free chunk
・8002012c = module link error
・8002012d = illegal object format (not PRX/PFX)
・8002012e = not found Module
・8002012f = not found Module file
・80020130 = Module file read error
・80020131 = memory in use
・80020132 = partition mismatch
・80020133 = module already started
・80020134 = module not started yet
・80020135 = module already stopped
・80020136 = module cannot stop
・80020137 = module not stopped yet
・80020138 = module cannot remove
・80020139 = exclusive load
・8002013a = Library is not linked yet
・8002013b = Library already exists
・8002013c = Library not found
・8002013d = illegal Library header
・8002013e = Library isused now
・8002013f = module already stopping
・80020140 = illegal off set value
・80020141 = illegal position code
・80020142 = illegal access code
・80020143 = module manager busy
・80020144 = illegal flag
・80020145 = cannot get module list
・80020146 = prohibit Load Module device
・80020147 = prohibit Load Exec device
・80020148 = unsupported PRX type
・80020149 = illegal permission call
・8002014a = cannot get module information
・8002014b = illegal Load Exec buffer
・8002014c = illegal Load Exec file name
・8002014d = There is no exit callback
・80020190 = no memory
・80020191 = illegal attr parameter
・80020192 = illegal thread entry address
・80020193 = illegal priority value
・80020194 = illegal stack size
・80020195 = illegal mode
・80020196 = illegal mask
・80020197 = illegal thread ID
・80020198 = not found thread
・80020199 = not found semaphore
・8002019a = not found event flag
・8002019b = not found message box
・8002019c = not found Vpool
・8002019d = not found Fpool
・8002019e = not found message pipe
・8002019f = not found alarm
・800201a0 = not found thread event handler
・800201a1 = not found callback
・800201a2 = thread already DORMANT
・800201a3 = thread already SUSPEND
・800201a4 = thread is not DORMANT
・800201a5 = thread is not SUSPEND
・800201a6 = thread is not WAIT
・800201a7 = now dispatch disabled
・800201a8 = WAIT timeout
・800201a9 = WAIT canceled
・800201aa = WAIT status released
・N800201ab = WAIT status released with callback
・800201ac = thread is terminated
・800201ad = semaphore counter zero
・800201ae = semaphore counter overflow
・800201af = event flag condition not occur
・800201b0 = this event flag cannot accept waits with multiple threads
・800201b1 = illegal event flag wait pattern
・800201b2 = message box have no message
・800201b3 = message pipe is full
・800201b4 = message pipe is empty
・800201b5 = wait object deleted
・800201b6 = illegal memory block
・800201b7 = illegal memory size
・800201b8 = illegal scratchpad address
・800201b9 = scratch pad in use
・800201ba = scratchpad not in use
・800201bb = illegal type
・800201bc = illegal size
・800201bd = illegal count
・800201be = not found vtimer
・800201bf = illegal vtimer ID
・800201c0 = illegal KTLS ID
・800201c1 = KTLS is full
・800201c2 = KTLS is busy
・80020258 = invalid such priority
・80020259 = device name is invalid
・8002025a = device name is unknown
・8002025b = pm information is registered already
・8002025c = pm information is not registered
・8002025d = major state is invalid value
・8002025e = request is invalid
・8002025f = request is unknown
・80020260 = unit number is invalid
・80020261 = cannot cancel request
・80020262 = pm information is invalid
・80020263 = argument is invalid
・80020264 = already target epower state
・80020265 = failed to change system power state
・80020266 = cannot change device power state
・80020267 = device does not support such power state
・800202bc = request to the DMAC failed
・800202bd = DMA operation is less or equal one
・800202be = the operation is already queued
・800202bf = the operation is already finished or not queueud
・800202c0 = the operation is already in transfer progress
・800202c1 = the operation is not assigned yet
・800202c2 = the sync operation timed out
・800202c3 = dma operation struct is already freed
・800202c4 = dma operation is used
・800202c5 = dma operation is empty
・800202c6 = DMA operation is aborted
・800202c7 = DMA operation is error
・800202c8 = physical DMA channel is already reserved
・800202c9 = physical DMA channel is not managed by dmac manager
・800202ca = there is a privilege address in link list
・800202cb = link list buffer is not enough
・800202cc = the operation is not assigned to physical DMA channel
・800202cd = the operation is child operation
・800202ce = it is too much than transferable datasize
・800202cf = argument is invalid
・80020320 = Too many open files
・80020321 = No such device
・80020322 = Cross-device link
・80020323 = Bad file descriptor
・80020324 = Invalid argument
・80020325 = Unsupported operation
・80020326 = Alias is already used
・80020327 = Cannot mount
・80020328 = Driver deleted
・80020329 = Async operation is busy
・8002032a = No async operation
・8002032b = Device is already registered
・8002032c = No current working directory
・8002032d = Filename too long
・800203e8 = DECI3 No such device or address
・800203e9 = DECI3 I/O error
・800203ea = DECI3 Not enough core
・800203eb = STDIO not opened
・8002044c = Parameter is not cache aligned
・8002044d = End of kernel error code Never use this name
PR
